|
Stage 5 modified - Zenoah
290 |
The fully modified engine built for maximum performance and reliability,
use with a 2" band pipe, rated at 6.5+hp.We have been building
engines for over 5 years and have set several speed records with our
engines. The modifications include: trued crank, intake and exhaust
duration adjusted, compression raised, transfer ports directed, extensive
piston mods, crank and bearings trued, flywheel balanced, precision
seals installed, modified 257 Walbro, stainless bolts, NGK plug, magneto
properly spaced, and topped with a custom cooling cap.
|
|
|
Zenoah 290 w/WT257 |
 |
Product Features
Increased cylinder volume from the 260M, for increased performance and
power
Easy to start and adjust
Same overall size and mounting dimensions as the 260M
Approximately 20% more horsepower
Displacement: 29 cc
Cylinders: 1
Total Weight: 59 oz
Carb Type: WT257
Note: This is a conversion engine as Zenoah does not make a
29cc Marine engine and has had the needed modifications to make it suitable
for marine use (piston relieved and exhaust timing adjusted). All parts
are genuine Zenoah. |
|
|
| Zenoah
29cc kit |
  |
This is the new water-cooled Zenoah 29cc top end kit.
This kit includes all needed to convert your existing 260 or 231 into
a 29cc.
Included: Champion Spark plug, cooling cap w/ fittings, insulator w/
gaskets, water-cooled 29cc jug with cap installed, piston, ring, wrist
pin w bearing and clips (2), base gasket.
(Note: Kit is completely stock. Like all other water-cooled Zenoah's,
I recommend turning the piston down to avoid heat and seizure. Let me
know if you need this done at the time of the purchase and I will take
care of it "No Charge". |
|
|
| Stinger
Drive |
Features:
This stinger drive suits most mono 23 to 27cc set ups. This stinger
drive is setup for a 1/4 drive.
|
 |
|
|
| Strut |
Features:
This strut suits all 23 to 27cc set ups. The blade length is 100mm/
3 15/16" and the distance between the transom and back of the strut
is 50mm/2" This strut is setup for a 1/4" prop shaft
|
 |
|
|
| 4"
Rudder assembly |
Precision Manufactured complete with Brass Bushing and
Dual water pick up. Dimensions: Blade 145mm/5 3/4" (with out water
nipples) Standoff Bracket 100mm/4"
|
 |
|
|
| Zenoah 260/231 billet cap |
 |
| This is a brand new billet water jacket for the Zenoah G230PUM and G260PUM
engines. This water jacket eliminates the two bolts used to secure the
stock water jacket to the cylinder and in place uses 4 bolts and spacers
that go from the water jacket directly into the crank case. |
|
|
Easy link system |
 |
| Zenoah Easy Link Carb Adapters allow modelers to run a control
rod straight through the firewall to the throttle arm of their Zenoah
engine’s carb without having to use the complicated bell-crank linkage
of the past. Zenoah’s Carb Adapters are available separately for
modelers who already own a Zenoah engine. The new adapters will include
all the necessary hardware and bolts, as well as clear installation instructions. |
|
|
| Ball Link |
 |
4-40 Ball Link |
|
|
Modified 260 top end package |
 |
The fully modified top end kit is a very good deal for the bargain
hunter. Kit comes with a full mod jug, piston, and topped with a custom
cooling cap.
Mods include:
Cylinder - intake and exhaust durations adjusted, transfers modified
to direct the flow, and compression increased with 95% of the work done
on a machine for consistency.
Piston - CNC cut with a 21 gram final weight
Cooling cap - Custom etched and water fittings opened for increased
cooling/water flow.
|
|
|
Stage 5 modified - Zenoah
Stroker |
The fully modified engine built for oval racing, use with a 2"
band pipe or our steel pipe, rated at 6+hp.We have been building engines
for over 4 years and have set several speed records with our engines.
The modifications include: 2mm CY stroker full circle crank, intake
and exhaust duration adjusted, compression raised, transfer ports directed,
extensive piston mods, crank and bearings trued, flywheel balanced,
precision seals installed, modified 257 Walbro, stainless bolts, NGK
plug, magneto properly spaced, and topped with a custom cooling cap.
|
|
|
| Zenoah / SIKK water-cooled
exhaust manifold |
 |
For use with 7/8" headers.
|
|
|
| Zenoah 260/231 Custom cooling
cap |
 |
| High-Flow Water Jacket |
|
|
| Zenoah 260/231 Custom cooling
cap |
 |
| Anodized Red |
|
|
| Zenoah 260/231 Custom cooling
cap |
 |
| Anodized Purple. |
|
|
Squish tool |
 |
If you plan on repairing a modified engine or modify your own this
is a must have to be able to set the squish to where it should be. (different
mods will call for different squish heights but the normal range is
.014 - .022 in a Zenoah SIKK) |
|
|
 |
| Aluminum throttle arm anodized red. |
|
|
K&S tubing cutter |
 |
K&S tubing cutter |
|
|
Sullivan starter belt |
 |
Use these with an electric starter. These belts are used with the
above pulleys and other similar pulleys. |
|
|
Sullivan
Tees and Elbows |
 |
| This is Sullivan's Large Fuel Tees and Elbows. Will fit 1/8" to
3/16" inner Diameter fuel tubing. Suitable for all fuel types. |
|
|
Zenoah Full circle bottom
end |
 |
This is the hot set up for FC engines, all parts but the precision
seals and adaptor are genuine Zenoah parts. The RF adaptor allows timing
to be advanced or retarded 6 degrees. Comes ready to use with crank,
case bored out), bearings, seals, precision seals, and flywheel/adaptor.
IMPBA LS27 legal |
|
|
Zenoah 2MM stroker full circle
circle bottom end |
 |
This features a 2mm stroker CY crank. Comes ready to use with crank,
case bored out), bearings, seals, precision seals, and copper base gaskets. |
|
|
| Compition
Marine Cables |
| CMDI cables are top quality cables. |
|
|
|
| American RC steel pipe |
  |
This system comes with manifold, Teflon o-rings, polished stainless
header, and pipe with built in muffler. We have dyno tested this pipe
and found it to be the best all around performing pipe out of 5 popular
pipes. This also features Teflon o-rings and our new high flow exhaust
manifold that can not let water into the pipe.
Set up directions |
|
|
| Bucks Radio Box |
 |
Very nice radio box, comes with: Box, lid, lid seal, rod seals, and
moisture pacs. |
|
|
|
|
|
| Drop engine mount |
 

|
Comes with throttle linkages, coil re locator, and stainless bolts.
This mount will fit the 230/231/260/QD25. |
|
|
 |
| |
|
 |
| |
|
 |
| |
|
Hitec Giant
scale 755MG servo |
 |
| A very strong long lasting servo (metal gears). |
| |
|
Expert Volt
meter |
 |
Key Features:
Check 4-cell or 5-cell Rx battery packs
Solid state circuitry
24" long cord with universal connector
compact in size 2 1/4" x 1 11/16" x 11/16"
Accurate within +-.04V for 4-cell packs and +- .05V for 5-cell packs
Overview:
It's late in the afternoon, and you've been boating most
of the day. The wind has finally subsided, and there's just enough time
for one more run before the sun sets. You're ready; how about your batteries?
With Expert's V300 Voltmeter, you'll know in seconds if it's safe to
float or if it's time to recharge.
The Expert V-300 Voltmeter features an LED bar graph display. 10 LED's
(3 green, 4 yellow, and 3 red) are displayed in a bar graph for easy
viewing on the current state of charge of your receiver battery pack.
Each LED's color corresponds to that of a stoplight: green for go, yellow
for warning, and red for stop-do not fly before recharging. Switch selectable,
you can test both 4-cell and 5-cell receiver packs under a 300 mA current
load to simulate the typical operating current.
Using the V-300 is very simple: Move the slide switch
to correspond to the appropriate voltage level of the pack being tested
(4.8V 4-cell or 6V 5-cell) and plug the V-300's universal connector
into the charge jack. In 10 seconds you have an accurate and stable
reading, so at a glance you know if you can safely go boating.
|
| |
|
| 3M Radio Box tape |
 |
| The best tape on the market for taping radio box lids down. Very thin,
seals very well, and does not leave residue. |
|
|
Starter pulley Zenoah / CY |
  |
Use these with an electric starter. These pulleys are easy to use
due to the diameter of the pulley making for easy starts. |
|
|
| Expert standard switch w/
charge cord |
 |
| Standard switch with charge cord |
|
|
| Dubro EZ Connectors (4-40) |
Dubro EZ connector 4-40 |
|
|
| Dubro EZ Connectors (256) |
 |
Dubro EZ connector 256 |
|
|
| Sullivan clevace |
 |
Sullivan 4-40 clevace |
|
|
| Antenna |
 |
A very nice antenna with a tapered ID for easy use.
Includes: tube, cap, CNC machined base, and stainless nut. |
|
|
|
Water outlet |
 |
| This fitting will bolt through the hull to expel water. |
|
|
| Octura Y567/2 B |
|
|
Octura 1667/2 B |
 |
|
|
| Octura 1967/2 B |
|
|
| Octura 2267/2 B |
|
|
| Octura 1470/2 B |
|
|
| Octura X470/2 B |
|
|
| Octura X670/2 B |
|
|
| Octura 2170/2 B |
|
|
| Octura 1475/2
B |
 |
|
|
| Octura M575/2 B |
|
|
| Octura 2175/2 B |
|
|
| Octura X482/2 B |
|
|
| Pipe mount |
 
|
|
|
|
| 8oz
jar of Cab-O-Sil |
 |
| Cab-O-Sil is basically a light powder fiberglass used to
thicken glue, epoxy, or resin. |
|
| |
| |
| |
| |
| |
| |